This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
2big_network_v2 [2011/11/01 15:14] – 82.234.233.9 | 2big_network_v2 [2013/07/07 17:04] (current) – fix typo in flash size starox | ||
---|---|---|---|
Line 7: | Line 7: | ||
* CPU ARM926EJ-S (ARMv5TE) 1200MHz | * CPU ARM926EJ-S (ARMv5TE) 1200MHz | ||
* SoC Kirkwood 88F6281_A0 | * SoC Kirkwood 88F6281_A0 | ||
- | * SDRAM memory 256MB, DDR2 533MHz | + | * SDRAM memory 256MB, DDR2 400MHz |
- | * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G) | + | * SPI flash, NOR 512KB (MACRONIX MX25L4005CMI-12G) |
* Ethernet Gigabit port (PHY MARVELL 88E1116R) | * Ethernet Gigabit port (PHY MARVELL 88E1116R) | ||
* 1 USB2 port, 1 connector host and 1 connector device | * 1 USB2 port, 1 connector host and 1 connector device | ||
Line 19: | Line 19: | ||
* Rear power switch | * Rear power switch | ||
* Serial: undocumented TTL serial interface (3.3V) | * Serial: undocumented TTL serial interface (3.3V) | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
===== OpenOCD ===== | ===== OpenOCD ===== | ||
Line 26: | Line 29: | ||
===== U-Boot ===== | ===== U-Boot ===== | ||
- | U-Boot mainline support is on-going. For more informations, | + | U-Boot mainline support is done. |
===== Linux ===== | ===== Linux ===== | ||
Line 33: | Line 36: | ||
===== Userspace ===== | ===== Userspace ===== | ||
+ | |||
+ | It is also possible to install Debian, look [[debian_install|here]]. | ||
===== LaCie System ===== | ===== LaCie System ===== | ||
- | This section describes | + | For more informations about the LaCie stock system, |
- | + | ||
- | ==== Boot ==== | + | |
- | + | ||
- | * Bootloader: TODO | + | |
- | * Boot method: U-Boot image on disk | + | |
- | * Kernel commandline: | + | |
- | + | ||
- | ==== Operating system ==== | + | |
- | + | ||
- | * Kernel: Linux 2.6.22.18 | + | |
- | * Coreutils: busybox | + | |
- | * HTTP: lighttpd | + | |
- | * FTP: ProFTPd | + | |
- | * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in / | + | |
- | * Bonjour: Avahi/ | + | |
- | * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in / | + | |
- | * Rsync: disabled by default, to enable it define a new daemon in /etc/initng on sda9 to launch "/ | + | |
- | * Deep sleep mode: can be enabled from the web interface, but if ssh has been enabled it is simpler to call / | + | |
- | + | ||
- | ==== Partitions ==== | + | |
- | + | ||
- | * sda1: extended, 2056 Mb | + | |
- | * sda2: xfs, md raid0/ | + | |
- | * sda5: swap, md raid1, 263,18 Mb | + | |
- | * sda6: Linux kernel U-Boot Image, 8,23 Mb | + | |
- | * sda7: ext3, md raid1, minimal root partition, 8,23 Mb | + | |
- | * sda8: ext3, md raid1, original firmware partition, 871,88 Mb | + | |
- | * sda9: ext3, md raid1, snapshots/ | + | |
- | * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb | + |