This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
network_space_v2 [2012/01/10 17:59] – added default uboot env 83.163.254.51 | network_space_v2 [2012/09/08 16:16] (current) – minor change 82.234.233.9 | ||
---|---|---|---|
Line 10: | Line 10: | ||
* SoC Kirkwood 88F6281_A0 | * SoC Kirkwood 88F6281_A0 | ||
* SDRAM memory 256MB, DDR2 267MHz | * SDRAM memory 256MB, DDR2 267MHz | ||
- | * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G) | + | * SPI flash, NOR 512kB (MACRONIX MX25L4005CMI-12G) |
* Ethernet Gigabit port (PHY MARVELL 88E1116R) | * Ethernet Gigabit port (PHY MARVELL 88E1116R) | ||
* 1 USB2 port, 1 connector host and 1 connector device (except for Internet Space v2) | * 1 USB2 port, 1 connector host and 1 connector device (except for Internet Space v2) | ||
Line 28: | Line 28: | ||
The boards are almost fully supported mainline. For more informations, | The boards are almost fully supported mainline. For more informations, | ||
- | |||
- | These are the default environment variables in the stock U-Boot provided by Lacie: | ||
- | baudrate=115200 | ||
- | loads_echo=0 | ||
- | rootpath=/ | ||
- | netmask=255.255.255.0 | ||
- | console=console=ttyS0, | ||
- | CASset=min | ||
- | MALLOC_len=1 | ||
- | ethprime=egiga0 | ||
- | bootargs_root=root=/ | ||
- | bootargs_end=::: | ||
- | image_name=uImage | ||
- | standalone=fsload 0x2000000 $(image_name); | ||
- | ethmtu=1500 | ||
- | mvPhoneConfig=mv_phone_config=dev0: | ||
- | mvNetConfig=mv_net_config=(00: | ||
- | usb0Mode=host | ||
- | yuk_ethaddr=00: | ||
- | netretry=no | ||
- | rcvrip=169.254.100.100 | ||
- | loadaddr=0x02000000 | ||
- | autoload=no | ||
- | ethact=egiga0 | ||
- | stderr=serial | ||
- | mainlineLinux=no | ||
- | enaMonExt=no | ||
- | enaCpuStream=no | ||
- | enaWrAllo=no | ||
- | pexMode=RC | ||
- | disL2Cache=no | ||
- | setL2CacheWT=yes | ||
- | disL2Prefetch=yes | ||
- | enaICPref=yes | ||
- | enaDCPref=yes | ||
- | sata_dma_mode=yes | ||
- | netbsd_en=no | ||
- | vxworks_en=no | ||
- | disaMvPnp=no | ||
- | enaAutoRecovery=yes | ||
- | start_lump=lump 3 | ||
- | resetdisk=ide reset | ||
- | bootdelay=0 | ||
- | boot_fail=lump | ||
- | kernel_addr=0x800000 | ||
- | productType_env=ASTON_KW | ||
- | primaryPart=6 | ||
- | secondaryPart=A | ||
- | resetFlag_env=0 | ||
- | bootargs=console=ttyS0, | ||
- | bootcmd=run disk_disk | ||
- | boot_disk4=disk ${kernel_addr} 1: | ||
- | boot_disk3=if disk ${kernel_addr} 0: | ||
- | boot_disk2=if disk ${kernel_addr} 1: | ||
- | boot_disk1=if disk ${kernel_addr} 0: | ||
- | boot_disk=if test ${resetFlag_env} -eq 0; then run boot_disk1; else run boot_disk3; fi | ||
- | disk_disk=run boot_disk; setenv bootargs console=ttyS0, | ||
- | ethaddr= #mac address | ||
- | ipaddr= #NAS ip | ||
- | ncip= #clunc connected ip | ||
- | serverip= #clunc connected ip | ||
- | stdin=nc | ||
- | stdout=nc | ||
- | |||
- | | ||
===== Linux ===== | ===== Linux ===== | ||
Line 100: | Line 35: | ||
===== Userspace ===== | ===== Userspace ===== | ||
- | ===== Auto power on ===== | + | It is also possible to install Debian, look [[debian_install|here]]. |
+ | |||
+ | ===== LaCie system | ||
- | Normally, after applying power, you have to push the button to turn on the ns2. If you want it to switch on automatically, you have to switch a bit in the i2c eeprom. | + | For more informations about the LaCie stock system, look [[lacie_stock|here]]. |
- | The bit is at offset 14 in the eeprom, changing it from 0 to 1 will enable auto switch on. | + | |
- | For more details see [[ubootforkirkwoodsocs# | + | |