User Tools

Site Tools


lacie_stock

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
lacie_stock [2012/09/08 16:11] – created 82.234.233.9lacie_stock [2012/09/08 16:33] (current) 82.234.233.9
Line 1: Line 1:
-====== LaCie stock system ======+====== LaCie operating systems ======
  
-===== EEPROM =====+This section gathers all informations about the different LaCie stock systems.
  
-==== Organization ====+===== Legacy system (before 2011-2012) ===== 
 + 
 +==== EEPROM ==== 
 + 
 +=== Organization ===
  
 The EEPROM is available for reading and writing under Linux at the pseudo file **/sys/bus/i2c/devices/0-0050/eeprom**. The EEPROM is available for reading and writing under Linux at the pseudo file **/sys/bus/i2c/devices/0-0050/eeprom**.
Line 15: Line 19:
 |15     |Fake sleepmode        |Used by the Lacie stock initramfs, it's FD and you can ignore it | |15     |Fake sleepmode        |Used by the Lacie stock initramfs, it's FD and you can ignore it |
  
-==== Auto power on ====+=== Auto power on ===
  
 Normally, after applying power, you have to push the button to turn on the ns2. If you want it to switch on automatically, you have to switch a bit in the i2c eeprom. Normally, after applying power, you have to push the button to turn on the ns2. If you want it to switch on automatically, you have to switch a bit in the i2c eeprom.
 The bit is at offset 14 in the eeprom, changing it from 0 to 1 will enable auto switch on. The bit is at offset 14 in the eeprom, changing it from 0 to 1 will enable auto switch on.
  
-===== U-Boot =====+==== Disk partitions ====
  
-==== Environment ====+  * sda1: extended, 2056 Mb 
 +  * sda2: xfs, md raid0/raid1, user data, the remaining part of the disk 
 +  * sda5: swap, md raid1, 263,18 Mb 
 +  * sda6: Linux kernel U-Boot Image, 8,23 Mb 
 +  * sda7: ext3, md raid1, minimal root partition, 8,23 Mb 
 +  * sda8: ext3, md raid1, original firmware partition, 871,88 Mb 
 +  * sda9: ext3, md raid1, snapshots/upgrades partition, 896,56 Mb 
 +  * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb 
 + 
 +==== U-Boot ==== 
 + 
 +=== Default environment ===
  
-These are the default environment variables in the stock U-Boot provided by Lacie: 
 <code> <code>
 baudrate=115200 baudrate=115200
Line 88: Line 102:
 stdout=nc stdout=nc
 </code> </code>
 +
 +=== Boot ===
 +
 +The Linux kernel is loaded from disk.
 +
 +==== Linux ====
 +
 +Here are the possible versions for the Linux kernel:
 +  * 2.6.22.18.
 +  * 2.6.31.14.
 +
 +Here are the possible versions for the Linux Marvell patch:
 +  * LSP 5.0.3
 +  * LSP 5.1.3
 +
 +==== Userland ====
 +
 +  * Coreutils: busybox
 +  * HTTP: lighttpd
 +  * FTP: ProFTPd
 +  * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in /snaps/00/etc/samba/smb.conf on sda9)
 +  * Bonjour: Avahi/Zeroconf
 +  * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in /etc/initng/runlevel/default.runlevel on sda8 and change root password in /snaps/00/etc/shadow on sda9)
 +  * Rsync: disabled by default, to enable it define a new daemon in /etc/initng on sda9 to launch "/usr/bin/rsync --daemon" and add it to /etc/initng/runlevel/default.runlevel
 +  * Deep sleep mode: can be enabled from the web interface, but if ssh has been enabled it is simpler to call /sbin/smart_shutdown
lacie_stock.1347113487.txt.gz · Last modified: 2012/09/08 16:11 by 82.234.233.9