User Tools

Site Tools


2big_network_v2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
2big_network_v2 [2011/11/01 15:14]
82.234.233.9
2big_network_v2 [2013/07/07 17:04] (current)
starox fix typo in flash size
Line 1: Line 1:
-====== Lacie 2big Network======+====== Lacie 2big Network v2 ======
  
 This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based). This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based).
Line 7: Line 7:
   * CPU ARM926EJ-S (ARMv5TE) 1200MHz   * CPU ARM926EJ-S (ARMv5TE) 1200MHz
   * SoC Kirkwood 88F6281_A0   * SoC Kirkwood 88F6281_A0
-  * SDRAM memory 256MB, DDR2 533MHz +  * SDRAM memory 256MB, DDR2 400MHz 
-  * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G)+  * SPI flash, NOR 512KB (MACRONIX MX25L4005CMI-12G)
   * Ethernet Gigabit port (PHY MARVELL 88E1116R)   * Ethernet Gigabit port (PHY MARVELL 88E1116R)
   * 1 USB2 port, 1 connector host and 1 connector device   * 1 USB2 port, 1 connector host and 1 connector device
Line 19: Line 19:
   * Rear power switch   * Rear power switch
   * Serial: undocumented TTL serial interface (3.3V)   * Serial: undocumented TTL serial interface (3.3V)
 +
 +{{:net2big_v2_00.jpg?640x480|2Big Network v2}}
 +{{:net2big_v2_01.jpg?640x480|2Big Network v2}}
  
 ===== OpenOCD ===== ===== OpenOCD =====
Line 26: Line 29:
 ===== U-Boot ===== ===== U-Boot =====
  
-U-Boot mainline support is on-going. For more informations, see our [[ubootforkirkwoodsocs|U-Boot for Kirkwood]] page.+U-Boot mainline support is done.
  
 ===== Linux ===== ===== Linux =====
Line 33: Line 36:
  
 ===== Userspace ===== ===== Userspace =====
 +
 +It is also possible to install Debian, look [[debian_install|here]].
  
 ===== LaCie System ===== ===== LaCie System =====
  
-This section describes the LaCie stock system+For more informations about the LaCie stock system, look [[lacie_stock|here]].
- +
-==== Boot ==== +
- +
-  * Bootloader: TODO +
-  * Boot method: U-Boot image on disk +
-  * Kernel commandline: console=ttyS0,115200 root=/dev/sda7 ro reset=0 productType=PRO_KW +
- +
-==== Operating system ==== +
- +
-  * Kernel: Linux 2.6.22.18 +
-  * Coreutils: busybox +
-  * HTTP: lighttpd +
-  * FTP: ProFTPd +
-  * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in /snaps/00/etc/samba/smb.conf on sda9) +
-  * Bonjour: Avahi/Zeroconf +
-  * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in /etc/initng/runlevel/default.runlevel on sda8 and change root password in /snaps/00/etc/shadow on sda9) +
-  * Rsync: disabled by default, to enable it define a new daemon in /etc/initng on sda9 to launch "/usr/bin/rsync --daemon" and add it to /etc/initng/runlevel/default.runlevel +
-  * Deep sleep mode: can be enabled from the web interface, but if ssh has been enabled it is simpler to call /sbin/smart_shutdown +
- +
-==== Partitions ==== +
- +
-  * sda1: extended, 2056 Mb +
-  * sda2: xfs, md raid0/raid1, user data, the remaining part of the disk +
-  * sda5: swap, md raid1, 263,18 Mb +
-  * sda6: Linux kernel U-Boot Image, 8,23 Mb +
-  * sda7: ext3, md raid1, minimal root partition, 8,23 Mb +
-  * sda8: ext3, md raid1, original firmware partition, 871,88 Mb +
-  * sda9: ext3, md raid1, snapshots/upgrades partition, 896,56 Mb +
-  * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb+
2big_network_v2.1320156877.txt.gz · Last modified: 2011/11/01 15:14 by 82.234.233.9