User Tools

Site Tools


2big_network_v2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
2big_network_v2 [2010/10/20 17:26] – created 79.20.137.2162big_network_v2 [2013/07/07 17:04] (current) – fix typo in flash size starox
Line 1: Line 1:
-====== Lacie 2big Network====== +====== Lacie 2big Network v2 ====== 
-The 2big Network v2 is a Linux-based NAS with a Marvell Board. It is the direct successor of the [[2big_network|2big Network]] (orion-based).+ 
 +This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based). 
 ===== Hardware ===== ===== Hardware =====
-  Board: TODO + 
-  * Cpu: TODO +  CPU ARM926EJ-S (ARMv5TE) 1200MHz 
-  * RAM: TODO +  * SoC Kirkwood 88F6281_A0 
-  * Network: 1x10/100/1000 Marvell Gigabit ethernet +  * SDRAM memory 256MB, DDR2 400MHz 
-  * USB: 2x2.0 ports, 1 host (to connect a mass storage device, an ups or a printer) and 1 gadget (to use the 2big as an usb hard drive+  * SPI flash, NOR 512KB (MACRONIX MX25L4005CMI-12G) 
-  * Storage: 2x1000/1500/2000 Gb Seagate SATA disks +  * Ethernet Gigabit port (PHY MARVELL 88E1116R) 
-  * LEDs: Frontal blue/red led, disk activity/functional led +  * 1 USB2 port, 1 connector host and 1 connector device 
-  * Flash: TODO+  * 2 SATA port and 1 SATA port multiplier x2 (JMicron JMB350 revA or revB) 
 +  * 2 SATA and 1 eSATA connectors 
 +  * I2C EEPROM, 512 bytes (24C04 type
 +  * 1 bi-color (blue and red) front LED 
 +  * 2 bi-color (blue and reddisk LEDs with CPLD SATA activity blink 
 +  * Front push button 
 +  * Rear power switch
   * Serial: undocumented TTL serial interface (3.3V)   * Serial: undocumented TTL serial interface (3.3V)
-===== System ===== 
-==== Boot ==== 
-  * Bootloader: TODO 
-  * Boot method: U-Boot image on disk 
-  * Kernel commandline: console=ttyS0,115200 root=/dev/sda7 ro reset=0 
-==== Operating system ==== 
-  * Kernel: TODO 
-  * Coreutils: busybox 
-  * HTTP: lighthttpd 
-  * FTP: ProFTPd 
-  * SMB: Samba 
-  * Bonjour: Avahi/Zeroconf 
-==== Partitions ==== 
-  * sda1: extended, 2056 Mb 
-  * sda2: xfs, md raid0/raid1, user data, the remaining part of the disk 
-  * sda5: swap, md raid1, 263,18 Mb 
-  * sda6: Linux kernel U-Boot Image, 8,23 Mb 
-  * sda7: ext3, md raid1, minimal root partition, 8,23 Mb 
-  * sda8: ext3, md raid1, original firmware partition, 871,88 Mb 
-  * sda9: ext3, md raid1, snapshots/upgrades partition, 896,56 Mb 
-  * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb 
-===== Mainline linux support ===== 
-Mainline support is scheduled for linux 2.6.37. 
  
-===== Clunc support ===== +{{:net2big_v2_00.jpg?640x480|2Big Network v2}} 
-This board works well with clunc; main LED will become red while clunc is active.+{{:net2big_v2_01.jpg?640x480|2Big Network v2}} 
 + 
 +===== OpenOCD ===== 
 + 
 +An unreliable configuration is available [[ftp://lacie-nas.org/openocd/net2big_v2.cfg|here]] 
 + 
 +===== U-Boot ===== 
 + 
 +U-Boot mainline support is done. 
 + 
 +===== Linux ===== 
 + 
 +The boards are almost fully supported mainline. For more informations, see our [[linuxforkirkwoodsocs|Linux for Kirkwood]] page. 
 + 
 +===== Userspace ===== 
 + 
 +It is also possible to install Debian, look [[debian_install|here]]. 
 + 
 +===== LaCie System ===== 
 + 
 +For more informations about the LaCie stock system, look [[lacie_stock|here]].
2big_network_v2.1287588371.txt.gz · Last modified: 2010/10/20 17:26 by 79.20.137.216