User Tools

Site Tools


2big_network_v2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Last revisionBoth sides next revision
2big_network_v2 [2011/11/01 15:11] 82.234.233.92big_network_v2 [2013/07/06 11:36] – change status of 2big2 starox
Line 1: Line 1:
-====== Lacie 2big Network====== +====== Lacie 2big Network v2 ====== 
-The 2big Network v2 is a Linux-based NAS with a Marvell Board. It is the direct successor of the [[2big_network|2big Network]] (orion-based).+ 
 +This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based). 
 ===== Hardware ===== ===== Hardware =====
  
   * CPU ARM926EJ-S (ARMv5TE) 1200MHz   * CPU ARM926EJ-S (ARMv5TE) 1200MHz
   * SoC Kirkwood 88F6281_A0   * SoC Kirkwood 88F6281_A0
-  * SDRAM memory 256MB, DDR2 533MHz+  * SDRAM memory 256MB, DDR2 400MHz
   * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G)   * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G)
   * Ethernet Gigabit port (PHY MARVELL 88E1116R)   * Ethernet Gigabit port (PHY MARVELL 88E1116R)
Line 17: Line 19:
   * Rear power switch   * Rear power switch
   * Serial: undocumented TTL serial interface (3.3V)   * Serial: undocumented TTL serial interface (3.3V)
 +
 +{{:net2big_v2_00.jpg?640x480|2Big Network v2}}
 +{{:net2big_v2_01.jpg?640x480|2Big Network v2}}
  
 ===== OpenOCD ===== ===== OpenOCD =====
Line 24: Line 29:
 ===== U-Boot ===== ===== U-Boot =====
  
-U-Boot mainline support is on-going. For more informations, see our [[ubootforkirkwoodsocs|U-Boot for Kirkwood]] page.+U-Boot mainline support is done.
  
 ===== Linux ===== ===== Linux =====
Line 31: Line 36:
  
 ===== Userspace ===== ===== Userspace =====
 +
 +It is also possible to install Debian, look [[debian_install|here]].
  
 ===== LaCie System ===== ===== LaCie System =====
  
-This section describes the LaCie stock system+For more informations about the LaCie stock system, look [[lacie_stock|here]].
- +
-==== Boot ==== +
- +
-  * Bootloader: TODO +
-  * Boot method: U-Boot image on disk +
-  * Kernel commandline: console=ttyS0,115200 root=/dev/sda7 ro reset=0 productType=PRO_KW +
- +
-==== Operating system ==== +
- +
-  * Kernel: Linux 2.6.22.18 +
-  * Coreutils: busybox +
-  * HTTP: lighttpd +
-  * FTP: ProFTPd +
-  * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in /snaps/00/etc/samba/smb.conf on sda9) +
-  * Bonjour: Avahi/Zeroconf +
-  * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in /etc/initng/runlevel/default.runlevel on sda8 and change root password in /snaps/00/etc/shadow on sda9) +
-  * Rsync: disabled by default, to enable it define a new daemon in /etc/initng on sda9 to launch "/usr/bin/rsync --daemon" and add it to /etc/initng/runlevel/default.runlevel +
-  * Deep sleep mode: can be enabled from the web interface, but if ssh has been enabled it is simpler to call /sbin/smart_shutdown +
- +
-==== Partitions ==== +
- +
-  * sda1: extended, 2056 Mb +
-  * sda2: xfs, md raid0/raid1, user data, the remaining part of the disk +
-  * sda5: swap, md raid1, 263,18 Mb +
-  * sda6: Linux kernel U-Boot Image, 8,23 Mb +
-  * sda7: ext3, md raid1, minimal root partition, 8,23 Mb +
-  * sda8: ext3, md raid1, original firmware partition, 871,88 Mb +
-  * sda9: ext3, md raid1, snapshots/upgrades partition, 896,56 Mb +
-  * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb+
2big_network_v2.txt · Last modified: 2013/07/07 17:04 by starox