This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
2big_network_v2 [2011/11/01 15:03] – 82.234.233.9 | 2big_network_v2 [2013/07/07 17:04] (current) – fix typo in flash size starox | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Lacie 2big Network====== | + | ====== Lacie 2big Network |
- | The 2big Network v2 is a Linux-based | + | |
+ | This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based). | ||
===== Hardware ===== | ===== Hardware ===== | ||
* CPU ARM926EJ-S (ARMv5TE) 1200MHz | * CPU ARM926EJ-S (ARMv5TE) 1200MHz | ||
* SoC Kirkwood 88F6281_A0 | * SoC Kirkwood 88F6281_A0 | ||
- | * SDRAM memory 256MB, DDR2 533MHz | + | * SDRAM memory 256MB, DDR2 400MHz |
- | * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G) | + | * SPI flash, NOR 512KB (MACRONIX MX25L4005CMI-12G) |
* Ethernet Gigabit port (PHY MARVELL 88E1116R) | * Ethernet Gigabit port (PHY MARVELL 88E1116R) | ||
* 1 USB2 port, 1 connector host and 1 connector device | * 1 USB2 port, 1 connector host and 1 connector device | ||
Line 18: | Line 20: | ||
* Serial: undocumented TTL serial interface (3.3V) | * Serial: undocumented TTL serial interface (3.3V) | ||
- | ===== System | + | {{: |
- | ==== Boot ==== | + | {{: |
- | * Bootloader: TODO | + | |
- | * Boot method: | + | ===== OpenOCD |
- | * Kernel commandline: | + | |
- | ==== Operating system | + | An unreliable configuration is available [[ftp:// |
- | * Kernel: Linux 2.6.22.18 | + | |
- | * Coreutils: busybox | + | ===== U-Boot ===== |
- | * HTTP: lighttpd | + | |
- | * FTP: ProFTPd | + | U-Boot |
- | * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in / | + | |
- | * Bonjour: Avahi/ | + | ===== Linux ===== |
- | * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in / | + | |
- | * Rsync: disabled by default, to enable it define a new daemon in /etc/initng on sda9 to launch "/ | + | The boards are almost fully supported mainline. For more informations, see our [[linuxforkirkwoodsocs|Linux for Kirkwood]] page. |
- | * Deep sleep mode: can be enabled from the web interface, but if ssh has been enabled it is simpler to call / | + | |
+ | ===== Userspace ===== | ||
- | ==== Partitions ==== | + | It is also possible to install Debian, look [[debian_install|here]]. |
- | * sda1: extended, 2056 Mb | + | |
- | * sda2: xfs, md raid0/ | + | |
- | * sda5: swap, md raid1, 263,18 Mb | + | |
- | * sda6: Linux kernel U-Boot Image, 8,23 Mb | + | |
- | * sda7: ext3, md raid1, minimal root partition, 8,23 Mb | + | |
- | * sda8: ext3, md raid1, original firmware partition, 871,88 Mb | + | |
- | * sda9: ext3, md raid1, snapshots/ | + | |
- | * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb | + | |
- | ===== Mainline linux support | + | ===== LaCie System |
- | Mainline support is currently being worked on. | + | |
- | ===== Clunc support ===== | + | For more informations about the LaCie stock system, look [[lacie_stock|here]]. |
- | This board works well with clunc; main LED will become red while clunc is active. | + |