Differences

This shows you the differences between two versions of the page.

--- 2big_network_v2 [2010/10/22 19:09] – Added note about sleep mode 79.20.137.216
+++ 2big_network_v2 [2013/07/06 11:36] – change status of 2big2 starox
@@ Line 1: / Line 1: @@
-====== Lacie 2big Network======
+====== Lacie 2big Network v2 ======
-The 2big Network v2 is a Linux-based NAS with a Marvell Board. It is the direct successor of the [[2big_network|2big Network]] (orion-based).
+This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based).
 ===== Hardware =====
-  * Board: 88F6281 A0 LE
-  * Cpu: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
+  * CPU ARM926EJ-S (ARMv5TE) 1200MHz
-  * RAM: 256 Mb DDR2
+  * SoC Kirkwood 88F6281_A0
-  * Network: 1x10/100/1000 Marvell Gigabit ethernet
+  * SDRAM memory 256MB, DDR2 400MHz
-  * USB: 2x2.0 ports, 1 host (to connect a mass storage device, an ups or a printer) and 1 gadget (to use the 2big as an usb hard drive)
+  * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G)
-  * eSata: 1 port
+  * Ethernet Gigabit port (PHY MARVELL 88E1116R)
-  * Storage: 2x1000/1500/2000 Gb Seagate SATA disks
+  * 1 USB2 port, 1 connector host and 1 connector device
-  * LEDs: Frontal blue/red led, disk activity/functional led
+  * 2 SATA port and 1 SATA port multiplier x2 (JMicron JMB350 revA or revB)
-  * Flash: TODO
+  * 2 SATA and 1 eSATA connectors
+  * I2C EEPROM, 512 bytes (24C04 type)
+  * 1 bi-color (blue and red) front LED
+  * 2 bi-color (blue and red) disk LEDs with CPLD SATA activity blink
+  * Front push button
+  * Rear power switch
   * Serial: undocumented TTL serial interface (3.3V)
-===== System =====
+{{:net2big_v2_00.jpg?640x480|2Big Network v2}}
-==== Boot ====
+{{:net2big_v2_01.jpg?640x480|2Big Network v2}}
-  * Bootloader: TODO
-  * Boot method: U-Boot image on disk
+===== OpenOCD =====
-  * Kernel commandline: console=ttyS0,115200 root=/dev/sda7 ro reset=0 productType=PRO_KW
-==== Operating system ====
+An unreliable configuration is available [[ftp://lacie-nas.org/openocd/net2big_v2.cfg|here]]
-  * Kernel: Linux 2.6.22.18
-  * Coreutils: busybox
+===== U-Boot =====
-  * HTTP: lighttpd
-  * FTP: ProFTPd
+U-Boot mainline support is done.
-  * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in /snaps/00/etc/samba/smb.conf on sda9)
-  * Bonjour: Avahi/Zeroconf
+===== Linux =====
-  * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in /etc/initng/runlevel/default.runlevel on sda8 and change root password in /etc/shadow on sda9)
-  * Rsync: disabled by default, to enable it define a new daemon in /etc/initng on sda9 to launch "/usr/bin/rsync --daemon" and add it to /etc/initng/runlevel/default.runlevel
+The boards are almost fully supported mainline. For more informations, see our [[linuxforkirkwoodsocs|Linux for Kirkwood]] page.
-  * Deep sleep mode: can be enabled from the web interface, but if ssh has been enabled it is simpler to call /sbin/smart_shutdown
+===== Userspace =====
-==== Partitions ====
+It is also possible to install Debian, look [[debian_install|here]].
-  * sda1: extended, 2056 Mb
-  * sda2: xfs, md raid0/raid1, user data, the remaining part of the disk
-  * sda5: swap, md raid1, 263,18 Mb
-  * sda6: Linux kernel U-Boot Image, 8,23 Mb
-  * sda7: ext3, md raid1, minimal root partition, 8,23 Mb
-  * sda8: ext3, md raid1, original firmware partition, 871,88 Mb
-  * sda9: ext3, md raid1, snapshots/upgrades partition, 896,56 Mb
-  * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb
-===== Mainline linux support =====
+===== LaCie System =====
-Mainline support is currently being worked on.
-===== Clunc support =====
+For more informations about the LaCie stock system, look [[lacie_stock|here]].
-This board works well with clunc; main LED will become red while clunc is active.

LaCie NAS wiki

User Tools

Site Tools

Differences

Page Tools