User Tools

Site Tools


2big_network_v2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Last revisionBoth sides next revision
2big_network_v2 [2010/10/20 18:05] 79.20.137.2162big_network_v2 [2013/07/06 11:36] – change status of 2big2 starox
Line 1: Line 1:
-====== Lacie 2big Network====== +====== Lacie 2big Network v2 ====== 
-The 2big Network v2 is a Linux-based NAS with a Marvell Board. It is the direct successor of the [[2big_network|2big Network]] (orion-based).+ 
 +This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based). 
 ===== Hardware ===== ===== Hardware =====
-  Board: TODO + 
-  * Cpu: TODO +  CPU ARM926EJ-S (ARMv5TE) 1200MHz 
-  * RAM: TODO +  * SoC Kirkwood 88F6281_A0 
-  * Network: 1x10/100/1000 Marvell Gigabit ethernet +  * SDRAM memory 256MB, DDR2 400MHz 
-  * USB: 2x2.0 ports, 1 host (to connect a mass storage device, an ups or a printer) and 1 gadget (to use the 2big as an usb hard drive+  * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G) 
-  * Storage: 2x1000/1500/2000 Gb Seagate SATA disks +  * Ethernet Gigabit port (PHY MARVELL 88E1116R) 
-  * LEDs: Frontal blue/red led, disk activity/functional led +  * 1 USB2 port, 1 connector host and 1 connector device 
-  * Flash: TODO+  * 2 SATA port and 1 SATA port multiplier x2 (JMicron JMB350 revA or revB) 
 +  * 2 SATA and 1 eSATA connectors 
 +  * I2C EEPROM, 512 bytes (24C04 type
 +  * 1 bi-color (blue and red) front LED 
 +  * 2 bi-color (blue and reddisk LEDs with CPLD SATA activity blink 
 +  * Front push button 
 +  * Rear power switch
   * Serial: undocumented TTL serial interface (3.3V)   * Serial: undocumented TTL serial interface (3.3V)
-===== System ===== 
-==== Boot ==== 
-  * Bootloader: TODO 
-  * Boot method: U-Boot image on disk 
-  * Kernel commandline: console=ttyS0,115200 root=/dev/sda7 ro reset=0 
-==== Operating system ==== 
-  * Kernel: TODO 
-  * Coreutils: busybox 
-  * HTTP: lighthttpd 
-  * FTP: ProFTPd 
-  * SMB: Samba (unix extensions disabled by default; to enable them, change the corresponding line in /snaps/00/etc/samba/smb.conf on sda9) 
-  * Bonjour: Avahi/Zeroconf 
-  * SSH: Openssh (disabled by default; to enable it, uncomment the corresponding line in /etc/initng/runlevel/default.runlevel on sda8) 
-==== Partitions ==== 
-  * sda1: extended, 2056 Mb 
-  * sda2: xfs, md raid0/raid1, user data, the remaining part of the disk 
-  * sda5: swap, md raid1, 263,18 Mb 
-  * sda6: Linux kernel U-Boot Image, 8,23 Mb 
-  * sda7: ext3, md raid1, minimal root partition, 8,23 Mb 
-  * sda8: ext3, md raid1, original firmware partition, 871,88 Mb 
-  * sda9: ext3, md raid1, snapshots/upgrades partition, 896,56 Mb 
-  * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb 
-===== Mainline linux support ===== 
-Mainline support is currently being worked on. 
  
-===== Clunc support ===== +{{:net2big_v2_00.jpg?640x480|2Big Network v2}} 
-This board works well with clunc; main LED will become red while clunc is active.+{{:net2big_v2_01.jpg?640x480|2Big Network v2}} 
 + 
 +===== OpenOCD ===== 
 + 
 +An unreliable configuration is available [[ftp://lacie-nas.org/openocd/net2big_v2.cfg|here]] 
 + 
 +===== U-Boot ===== 
 + 
 +U-Boot mainline support is done. 
 + 
 +===== Linux ===== 
 + 
 +The boards are almost fully supported mainline. For more informations, see our [[linuxforkirkwoodsocs|Linux for Kirkwood]] page. 
 + 
 +===== Userspace ===== 
 + 
 +It is also possible to install Debian, look [[debian_install|here]]. 
 + 
 +===== LaCie System ===== 
 + 
 +For more informations about the LaCie stock system, look [[lacie_stock|here]].
2big_network_v2.txt · Last modified: 2013/07/07 17:04 by starox