This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
2big_network_v2 [2010/10/20 18:00] – 79.20.137.216 | 2big_network_v2 [2013/07/06 11:36] – change status of 2big2 starox | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Lacie 2big Network====== | + | ====== Lacie 2big Network |
- | The 2big Network v2 is a Linux-based | + | |
+ | This page is relevant for the LaCie NAS 2Big Network v2. It is the direct successor of the [[2big_network|2big Network]] (orion-based). | ||
===== Hardware ===== | ===== Hardware ===== | ||
- | | + | |
- | * Cpu: TODO | + | |
- | * RAM: TODO | + | * SoC Kirkwood 88F6281_A0 |
- | * Network: 1x10/ | + | * SDRAM memory 256MB, DDR2 400MHz |
- | * USB: 2x2.0 ports, 1 host (to connect a mass storage | + | * SPI flash, NOR 512MB (MACRONIX MX25L4005CMI-12G) |
- | * Storage: 2x1000/ | + | * Ethernet |
- | * LEDs: Frontal | + | * 1 USB2 port, 1 connector |
- | * Flash: TODO | + | * 2 SATA port and 1 SATA port multiplier x2 (JMicron JMB350 revA or revB) |
+ | * 2 SATA and 1 eSATA connectors | ||
+ | * I2C EEPROM, 512 bytes (24C04 type) | ||
+ | * 1 bi-color (blue and red) front LED | ||
+ | * 2 bi-color (blue and red) disk LEDs with CPLD SATA activity | ||
+ | * Front push button | ||
+ | * Rear power switch | ||
* Serial: undocumented TTL serial interface (3.3V) | * Serial: undocumented TTL serial interface (3.3V) | ||
- | ===== System ===== | ||
- | ==== Boot ==== | ||
- | * Bootloader: TODO | ||
- | * Boot method: U-Boot image on disk | ||
- | * Kernel commandline: | ||
- | ==== Operating system ==== | ||
- | * Kernel: TODO | ||
- | * Coreutils: busybox | ||
- | * HTTP: lighthttpd | ||
- | * FTP: ProFTPd | ||
- | * SMB: Samba | ||
- | * Bonjour: Avahi/ | ||
- | ==== Partitions ==== | ||
- | * sda1: extended, 2056 Mb | ||
- | * sda2: xfs, md raid0/ | ||
- | * sda5: swap, md raid1, 263,18 Mb | ||
- | * sda6: Linux kernel U-Boot Image, 8,23 Mb | ||
- | * sda7: ext3, md raid1, minimal root partition, 8,23 Mb | ||
- | * sda8: ext3, md raid1, original firmware partition, 871,88 Mb | ||
- | * sda9: ext3, md raid1, snapshots/ | ||
- | * sda10: filled with zeroes (may be used for an alternate kernel), 8,23 Mb | ||
- | ===== Mainline linux support ===== | ||
- | Mainline support is currently being worked on. | ||
- | ===== Clunc support ===== | + | {{: |
- | This board works well with clunc; main LED will become red while clunc is active. | + | {{: |
+ | |||
+ | ===== OpenOCD ===== | ||
+ | |||
+ | An unreliable configuration is available [[ftp:// | ||
+ | |||
+ | ===== U-Boot ===== | ||
+ | |||
+ | U-Boot mainline | ||
+ | |||
+ | ===== Linux ===== | ||
+ | |||
+ | The boards are almost fully supported mainline. For more informations, | ||
+ | |||
+ | ===== Userspace ===== | ||
+ | |||
+ | It is also possible to install Debian, look [[debian_install|here]]. | ||
+ | |||
+ | ===== LaCie System ===== | ||
+ | |||
+ | For more informations about the LaCie stock system, look [[lacie_stock|here]]. |