User Tools

Site Tools


2big_network

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
2big_network [2010/03/29 07:41] – BPtqjPGE 82.128.240.1672big_network [2011/10/10 10:34] (current) 188.201.122.243
Line 1: Line 1:
-BBoCRg  <href="http://whnlwjdqbvhw.com/">whnlwjdqbvhw</a>[url=http://edoegfpjchsa.com/]edoegfpjchsa[/url][link=http://tanwnblybnuy.com/]tanwnblybnuy[/link]http://uiuqdhdpaoej.com/+====== Lacie 2big Network====== 
 +The 2big Network is Linux-based NAS with a Marvell Board. 
 +===== Hardware ===== 
 +  * BoardMV-88fxx81 
 +  * Cpu: Marvell Orion ARM926EJ 400 Mhz 
 +  * RAM: 64 Mb DDR2 
 +  * Network: 1x10/100/1000 Marvell Gigabit ethernet 
 +  * USB: 2x2.0 ports 
 +  * Storage: 2x500/1000 Gb SATA disks 
 +  * LEDs: Frontal blue/red leddisk activity/functional led 
 +  * Flash: 512 Kb MX29LV400CBTC-70G 
 +  * Serial: undocumented TTL serial interface (3.3V) 
 +===== System ===== 
 +==== Boot ==== 
 +  * BootloaderU-Boot 1.1.1 (Jun 15 2007 - 08:56:23) Marvell version: 1.7.3 - LaCie version: 1.4.alpha_3 
 +  * Boot method: U-Boot image on disk 
 +  * Kernel commandline: console=ttyS0,115200 root=/dev/sda7 ro reset=0 
 +==== Operating system ==== 
 +  * Kernel: linux-2.6.12.6-arm1-lacie5e 
 +  * Coreutils: busybox 
 +  * FTP: ProFTPd 
 +  * SMB: Samba 
 +  * Bonjour: Avahi/Zeroconf 
 +==== Partitions ==== 
 +  * sda1: extended, 980 Mb 
 +  * sda2: xfs, md linear/raid1user data, the remaining part of the disk 
 +  * sda5swap, md raid1, 130 Mb 
 +  * sda6: Linux kernel U-Boot Image, 8 Mb 
 +  * sda7: ext3, md raid1, minimal root partition, 8 Mb 
 +  * sda8: ext3, md raid1, original firmware partition, 130 Mb 
 +  * sda9: ext3, md raid1, snapshots/upgrades partition, 696 Mb 
 +  * sda10: filled with zeroes (may be used for an alternate kernel), 8 Mb 
 +===== Mainline linux support ===== 
 +Mainline support was added in linux 2.6.32 and the default config file for Orion boards works. However, this board by default has a wrong arcNumber (526), that prevents a normal kernel from booting. A solution is to edit "mach-types" in the kernel source tree and change 2big network number to 526. Apart from that, there is full support for every hardware component, including LEDs. 
 + 
 +===== Clunc support ===== 
 +This board works well with clunc; main LED will become red while clunc is active.
2big_network.1269841312.txt.gz · Last modified: 2010/03/29 07:41 by 82.128.240.167